aftercare & MAINTENACE Guide

---

Window Tint is applied in the inner glass. 

Avoid rolling down the windows for 48 hours. 

The automatic roll-down upon opening the door will not interfere.

You may notice moisture in the film, its normal, do not push or touch any bubbles, as this may cause creasing. 

You may clean the inside of the glass after 48-hour cure time. 

Use an ammonia-free glass cleaner or a solution of distilled water. 

Wipe the windows gently with a microfiber cloth or a soft cotton cloth. 

Do not rub hard or use abrasive materials.

Avoid rain/water for the first 7 days (no vehicle washing). 

Plan to Leave it in the sun as much as possible. 

You may notice moisture or bubbles; this is normal and will dissipate in the sun. 

PPF inspection is advised 2-weeks/1-month after PPF.  Plan to come back for a check-up.

 DO NOT wax for 30-days. 

Periodic washing and waxing are recommended. Hand wash with soap and water. 

Wax once or twice a year with a non-abrasive wax for added protection and to maintain gloss.

Keep your pressure washer at least 2-feet away, use low PSI and wide fan tip. Avoid aiming the pressure washer directly at edges or seams. 

To prevent lifting, avoid automatic car washes, spraying the PPF with high pressure nozzle hose, high powered pressured steam or power washer with high PSI.

Improper wash technique and brushed washes can damage the self-healing topcoat and/or the PPF. 

PPF takes a full 30-days to cure and during this period, there may be some haze and condensation.  

Avoid rain and washing for 14 days. Avoid the use of automatic car washing with brushes. 

No waxing, buffing or California dusters. 

Do not let contaminates like bird droppings remain on any surface, safely remove as soon as possible. Remove bug splat and bird poop immediately with soap, water and microfiber towel (460 GSM or Higher) Avoid using Kirkland Yellow towels from Costco, as it can scratch your paint. 

Use touch-less tunnel washes and dry with compressed air. 

GYEON WASH MAINTENANCE GUIDE.

Wheels and Tires: 

Make sure wheels and brakes are fully cooled down before starting any wash procedure. 

Pressure wash the wheel and wheel-arches first to remove a maximum of debris. 

Spray heavily Q2M Iron Wheel Cleaner on the entire wheel and let it sit for 3-4 mins but don't let dry. 

Use Wheel mitt to agitate the solution in and out the wheels. 

Rinse heavily and repeat if needed. 

Pre-Wash:

Make sure your vehicle is fully cooled down before starting any wash procedure.

If you have access to a foam lance, fill it with Q2 Foam (dilution of 1:5 to 1:15) and spray heavily on your vehicle from top to bottom. 

Let it sit for 3-4 minutes to loosen all dirt and debris off your paint. Rinse heavily. 

Wash and Decontamination (2 bucket method):

Fill both buckets with 10L of water and pour 15ML of Q2M Restart wash into 1 bucket. 

Start washing the vehicle from top to bottom in Straight line motion. 

Rinse your mitt after each panel. 

Do not let the shampoo dry. Rinse Heavily. 

Chemical decontamination will remove deep contamination embedded in your coating and will help restore initial hydrophobicity. 

Dry with compressed air. 

To boost beading and water repellency, spray GYEON Ceramic Detailer to restore hydrophobicity and instant gloss monthly. 

FOR THE FIRST 48 HOURS. 

Don't Soak It - avoid car washes, driving in rain or using wipers when possible. 

Let It Dry - expose your windshield to the sun for the first few days to speed up curing. 

Give It Time - you might see some distortion initially. this disappears once ExoShield is cured. 

_______________________________________________

1. Avoid using your wiper blades or driving in the rain for the first 48 hours after installation when possible.  GT3+ can take as much as 7 days to fully cure. To speed up the curing process, we suggest leaving your vehicle in a dry, sunny environment. During the curing time, you may notice water spots or a slight distortion in the film - this is normal and will go away once fully cured.

2. When possible, keep the surface of ExoShield GT3+ clean and free of contaminants such as bird droppings, dirt, oil, sap, or other chemicals.

3. DO NOT pressure wash your windshield when ExoShield GT3+ is installed. Instead, simply wash your windshield gently with soap and water or use a touchless car wash regularly to keep it clean.

4. Take care of your wiper blades by gently wiping them with a damp microfiber cloth on a regular basis. This will ensure that you’re removing any trapped dirt or grit that can get stuck in the wiper blades and prematurely scratch the film.

5. Avoid using harsh chemicals to clean your windshield when GT3+ is installed. Stick to an ammonia-free (or tint-safe) glass cleaner and only use ExoShield-approved coatings. In some cases, adding a ceramic coating to the surface of GT3+ may help to extend its lifetime. We recommend discussing these options with your installer at the time of purchase.

7. If you start to notice severe scratching and haziness in the film at the end of the film’s usable life that is limiting your visibility, it’s important to remove ExoShield as soon as possible for your own safety.